RESIN - 4369 Anuncios

Jueves 24 agosto 2023

Cantidad : 1000kg - Precio : 400-800CNY

CA Series-550CA30 PEEK carbon fiber reinforcement is a 30% carbon fiber reinforced PEEK plastic material, the addition of carbon fiber significantly increased the material's wear resistance and high temperature mechanical strength, thermal conductivity is pure resin G series 3 times...

Jueves 24 agosto 2023

Cantidad : Carton - Precio : 400-800CNY

PEEK polymer raw material is a kind of semicrystalline aromatic polvmer and its main chain of macromole is consist of arvl. ketone, and ether. PEEK plastic raw material has the properties of heat resistance, chemical stability as thermosetting plastics, and good processability as thermoplastics...

Miércoles 23 agosto 2023

For parts with complex structure, stainless steel 3d printing service can realize integral printing forming, avoiding mass increase and potential quality defects caused by welding forming a complex part after disassembling and manufacturing, and even canceling the assembly of complex parts...

Miércoles 23 agosto 2023

SLA printing is focused on the surface of a light cured material, which is solidified from point to line and line to surface. SLA printing of SLA 3d printing companies Proto Mold enables a wide selection of materials, extremely high feature resolution and high quality surface treatment...

Miércoles 23 agosto 2023

EDI is a pure water manufacturing technology that combines ion exchange technology, ion exchange membrane technology and ion electromigration technology. It skillfully combines electrodialysis and ion exchange technology, uses high voltage of electrodes at both ends to move charged ions in water...

Miércoles 23 agosto 2023

EDI module is usually placed behind the reverse osmosis system, which not only overcomes the lack of deep desalination of reverse osmosis effluent, but also further removes trace carbon dioxide, residual salt, silicon dioxide, boron and total organic carbon plasma in RO water, greatly...

Martes 22 agosto 2023

What is FR4? FR4 is the name of a type of epoxy glazing material. fr stands for flame retardant. 4 refers to the factors that differentiate it from other materials. FR4 means two things. The material. As a construction material, it refers to epoxy laminates reinforced with glass fibers...

Martes 22 agosto 2023

Precio : USD1500 to USD3000

It is mainly used as plasticizer for producing unsaturated polyester resin, additive for high-grade lubricating oil, and also as polymerization inhibitor, stabilizer and insecticide. Neopentyl Glycol CAS No 126 30 7 Basic Information Product Name Neopentyl Glycol Multiple Names 2...

Martes 22 agosto 2023

Precio : USD1500 to USD3000

This product is non-toxic plasticizer, which can be used as plasticizer of PVC, cellulose resin and synthetic rubber. For non-toxic PVC granulation, food packaging containers, children's toys, medical products, films, plates, cellulose coatings and other products. Acetyl Tributyl...

Martes 22 agosto 2023

Precio : USD1500 to USD3000

Propylene glycol can be used in the manufacture of unsaturated polyester, liquid saturated polyester, thermoplastic polyester resin (PET and PBT modification), alkyd resin, polyurethane resin, double ester type plasticizer, lubricant, also used in cosmetics, pharmaceuticals, etc...

Martes 22 agosto 2023

Shijin watch has devoted itself to wooden watches for years. As the leading wood watch factory in China, we have implemented an innovation that we combine the wood with stainless steel as the original material of watches by rich experiences in horology and professional in-house wood...

Martes 22 agosto 2023

As a leading printing consumables manufacturer with over 42 years of experience, Print-Rite is dedicated to delivering innovative, patent-safe, high-quality, and eco-friendly products. Our consumables are designed to meet the most rigorous safety standards, ensuring that you can print...

Martes 22 agosto 2023

Looking for a high-quality, affordable printing solution direct from printer ribbon supplier and printer ribbon manufacturer? Print Rite printer ribbon delivers crisp, clear prints with every use. We have wax resin ribbon, thermal printer ribbon, label printer ribbon, printer tape...

Jueves 10 agosto 2023

Cantidad : 100pcs - Precio : USD0.10 -USD2.5/PCS

An oil filter is a filter designed to remove particals and contaminants from engine oil, transmission oil, lubricating oil, or hydraulic oil. Their primary use is in internal-combustion engines for motor vehicles (both on- and off-road ), powered aircraft, railway locomotives, ships and boats...

Martes 08 agosto 2023

Cantidad : 10 million - Precio : 0.4-1.2 usd per sqm

Egret vinyl tape is made of soft polyvinyl chloride (PVC) film as the base material, coated with rubber pressure sensitive adhesive, with good insulation, flame resistance, voltage resistance, cold resistance and other characteristics, suitable for automobile wiring, wire winding...

Martes 08 agosto 2023

Cantidad : 10 million - Precio : 0.4-1.2 usd per sqm

Egret so-called vinyl electrical tape is used a lot for wrapping the wire harness, so it is also called PVC wire harness tape. Important to realize, the main difference with non-adhesive pvc tape is about the glue. The base material is pure PVC resin and coated with aggressive synthetic...

Martes 08 agosto 2023

Cantidad : 10 million - Precio : 0.4-1.2 usd per sqm

Polyethylene fiber mesh laminated with foil is very popular in HVAC industry. It can used for wrapping the air ducts and laminating the glass wool or rock wool thermal insulation, duct board joints applications. It can be either easy tear or hard tear as per customers requirements...

Martes 08 agosto 2023

Cantidad : 10 million - Precio : 0.4-1.2 usd per sqm

Egret so-called pvc pipe wrap tape is used a lot for wrapping air ducts, so it is also called PVC pipe wrap tape. Important to realize, the main difference with non adhesive pvc tape is about the glue. The base material is pure PVC resin, and coated with aggressive synthetic rubber adhesive...

Martes 08 agosto 2023

Precio : 2.8-3.2USD

Plastic molds are tools that are matched with plastic mold making machines in the plastic processing industry to give plastic products a complete configuration and precise dimensions. Due to the wide variety of plastics and processing methods, and the complex and simple structures...

Martes 08 agosto 2023

Precio : 2.8-3.2USD

Insert molding service is one category of injection molding that allows preformed parts or components, usually metal inserts, to be inserted into the plastic molded parts and to have a final product in one-step process. Insert moulding has characteristics as below: A combination of two parts...

Martes 08 agosto 2023

Precio : 2.8-3.2USD

What materials are used in injection moulding? Materials used in injection moulding generally include abs molding, nylon injection molding, polycarbonate injection molding, PP injection molding, PVC injection molding, HDPE injection molding, and so on. Feel free to check out the injection...

Martes 08 agosto 2023

Precio : 2.8-3.2USD

Plastic Injection Molding Plastic Injection Molding Plastic injection moulding is a method of making plastic products. The molten plastic is injected into the mold by pressure, and then cooled and molded to obtain various plastic parts. There are mechanical injection molding machines...

Martes 08 agosto 2023

We can provide you with up to 64 layers, 12oz copper, HDI, high frequency, high TG, flex, MC pcb from prototype to mass production. As a rigid pcb manufacturer, Fastlink Electronics offers the highest quality printed circuit boards at the most competitive pricing. Whether you need...

Martes 08 agosto 2023

On the mounted flap wheel for drill, the flap made of coated abrasive is arranged radially around the tool axis in a fan-shaped structure. Their flexibility enables them to fully adapt to the contour of the workpiece. Abrasive particles are embedded in a strong and flexible cloth...

Martes 08 agosto 2023

The flexibility of 8 inch flap wheel enables them to fully adapt to the contour of the workpiece. Abrasive particles are embedded in a strong and flexible cloth backing material through a resin adhesive. Flap Wheel 3/8inch Specification: Diameter: 3/8 inch=10mm Max. RPM: 25000 RPM Raw Materials...

Martes 08 agosto 2023

On the mounted abrasive flap wheel, the flap made of coated abrasive is arranged radially around the tool axis in a fan-shaped structure. Their flexibility enables them to fully adapt to the contour of the workpiece. Abrasive particles are embedded in a strong and flexible cloth backing...

Martes 08 agosto 2023

On the Mounted Small Flap Wheel, the flap made of coated abrasive is arranged radially around the tool axis in a fan-shaped structure. Their flexibility enables them to fully adapt to the contour of the workpiece. Abrasive particles are embedded in a strong and flexible cloth backing...

Martes 08 agosto 2023

On the Mounted Emery Flap Wheel, the flap made of coated abrasive is arranged radially around the tool axis in a fan-shaped structure. Their flexibility enables them to fully adapt to the contour of the workpiece. Abrasive particles are embedded in a strong and flexible cloth backing...

Martes 08 agosto 2023

On the Mounted Flap Wheel, the flap made of coated abrasive is arranged radially around the tool axis in a fan-shaped structure. Their flexibility enables them to fully adapt to the contour of the workpiece. Abrasive particles are embedded in a strong and flexible cloth backing material...

Martes 08 agosto 2023

On the mounted aluminium oxide flap wheel, the flap made of coated abrasive is arranged radially around the tool axis in a fan-shaped structure. Their flexibility enables them to fully adapt to the contour of the workpiece. Abrasive particles are embedded in a strong and flexible...