CAVITY - 1099 Anuncios

Sábado 10 septiembre 2022

Hot press vacuum press is used for the test parameters of the material properties, including the fluidity of composite materials, resin fluidity, and gel time. The composite material is formed after hot pressing and curing. The parameters of temperature and pressure in the hot pressing...

Sábado 10 septiembre 2022

Precio : 1-10usd

The ir dichroic mirror, augmented by colour filters that perfected their colour-selective action, directed a blue image to the first tube, a green image to the second, and a red image to the surface. Dichroic Mirror Specification Material BK7 or Fused Silica Design Wavelength 546...

Jueves 01 septiembre 2022

Cantidad : 30 sets of - Precio : $1,000-$10,000

2k injection molding is a manufacturing process that refers to molding two materials or colors into one plastic part. This technology combines two materials or two colors into one ending plastic part by using a 2K automotive plastic injection moulding machine. The selection of the...

Sábado 27 agosto 2022

Features of sewer knife gate valve Full bore design for high media throughput capacity; U-shaped gasket with good sealing effect; Gate plate with gate function, good shut-off effect, can effectively shut off all kinds of debris in the media, to solve the leakage phenomenon after shut-off...

Jueves 25 agosto 2022

iWORKHUB's Mobile TV Cart Rotational is designed to support the features and functions of the 50.5" Microsoft® Surface™ Hub 2S/2X, 55" and 65" Samsung Flip 2 displays. These commercial monitor floor television rotational carts/stands on wheels can effectively allow the display to...

Jueves 25 agosto 2022

Ace-tec is a reliableoral care products manufacturer. Our oral care product uses the rapid rotation or vibration of the motor to generate high-frequency vibrations in the brush head, the vibration of the bristles can promote the blood circulation of the oral cavity and affect the gum tissue...

Jueves 25 agosto 2022

Cantidad : 500000 Pie - Precio : US $1 - 3,000 / Set

Description Due to the distinctive nature of the environmental conditions and operating conditions of the process, a typical ball valve is not sufficient and the system demands high performance. Using the top entry structure, it is not needed to remove the ball valve from the line...

Jueves 25 agosto 2022

POER Smart provides the programmable wifi enabled central heating programmer. We have wifi water heater thermostats and wifi electric underfloor heating smart thermostats for your choice. The wifi boiler control thermostat was built-in a wifi module. With this module, the wifi central...

Miércoles 24 agosto 2022

Laundry Basket Knit Style Laundry basket mould with delicate knit pattern.The mould cavity adopts 8 slider design.This set of product includes 3 pairs of mould and the basket requires 1000T injection machine. LAUNDRY BASKET KNIT STYLE LAUNDARY BASKET MOULD DETAILS Item No.: JP33-1...

Sábado 20 agosto 2022

Cantidad : 5000 - Precio : 0-100

1.Overview of Engine Oil Pan The oil pan is an important part of automobile engine and an indispensable part of engine lubrication system.By sealing the lower crankcase, the oil on the moving surface of the engine is collected and stored, oil to prevent aging, part of heat loss,at...

Miércoles 17 agosto 2022

Precio : 100USD

The pressure sensor produced by Tianguang company can be divided into resistance strain type and diffused silicon type. According to the structure, each type is divided into two types: with a cavity and without a cavity. The cavity has high accuracy and a wide range; the cavityless...

Miércoles 17 agosto 2022

Cantidad : 1 set - Precio : 5000USD-30000USD

Two Shot Tool Construction Part two shot tool construction saves the injection machine quantity and plant area, lower the labor cost and minimize the part handling, although mould cost is high but later process cost is lower, not on... Two Shot Plastic Injection Molding Parts How...

Miércoles 17 agosto 2022

Cantidad : 1 set - Precio : 5000USD-30000USD

Sewing Machine Frame Mould Large plastic frame plastic injection sewing molds, suited for oversize embroidery projects. Mould Name: Embroidery Machine Frame Mould Part Material: Pa 66 GF50% Product Description Large Embroidery hoop inner frame Mould Cavity: 1 Cavity Mould Size: 400*600*380...

Miércoles 17 agosto 2022

Cantidad : 1 set - Precio : 5000USD-30000USD

Injection Plastic Mold Injection plastic mold is another name for plastic injection mold. This is just how people in various places call injection molds differently. The injection plastic mold can be made as single cavity plastic mold or multi cavities injection mold according to...

Miércoles 17 agosto 2022

Cantidad : 1 set - Precio : 5000USD-30000USD

Mould Name: Precision Automotive Plastics Mould Part Material: PA66 G30 Product Description: BODY plastic Mould Cavity: Cavities Mold Mould Cavity Steel: 2344ESR Mould Injection System: hot runner Mould Ejection System: ejector pin Mould Cycle Time: 26's Mould Life Cycle: 1,000,000 Lead Time...

Miércoles 17 agosto 2022

Cantidad : 1 set - Precio : 5000USD-30000USD

Mould Type: Plastic Precision Car Parts Mould Production Material: PC, PP, PA6, PA66, PE, ABS, HDPE, TPE, TPU, PET, PPS, POM, PBT, PMMA, PPS, SAN, etc. No of Cavities: Single or Multi cavity Core Material: 2344, S136,H13,S7, NAK80,SS420, P20 and other steel according to customer mould...

Viernes 12 agosto 2022

As a professional CNC Die Sinker EDM Machine manufacturer, we aim at providing you erosion machines with high quality. EDM sinker for sale is waiting for your contact with a warm welcome. We are available if you have any questions about sinker edm machine for sale. What is CNC Die...

Viernes 12 agosto 2022

DMNC Provides Complete Solution Of EDM Machining Technology With 30+ Years' Experience, Continuous Innovation, Strict Quality Control, and Swift Service. The cnc edm die sinking machine for sale can machine deep ribs faster with more precision, as the CNC incorporates technology...

Viernes 12 agosto 2022

Cantidad : 1000

Soxi is one of the top plastic material dryer manufacturers, our plastic drying machine will avoid the following questions. In the plastic auxiliary machinery, the plastic in the resin state easily absorbs moisture from the air. In another word, the moisture absorbed during storage...

Viernes 12 agosto 2022

Cantidad : 1000

Soxi is one of the top industrial chiller manufacturers in China. Industrial water chiller system plays an important part in the plastic moulding process, injecting frozen water into the flow channel inside the mold, cooling the mold through heat exchange, maintaining the temperature...

Viernes 12 agosto 2022

Guitar Cases And Bags Size : 41", made of 600d water-resistant oxford fabric with 10mm padded sponge protecting your guitar from unexpected collision. The convenient carry handle on the back and side easy carrying while keeping the bag vertical. As an innovative guitar case maker...

Martes 09 agosto 2022

Sand casting china is the most commonly applied method for casting the metal part. It suits most of the raw materials, ferroalloy, and non-ferroalloy both can be used to do the sand casting. Types of sand casting is able to produce the part varying from several gram weight to dozens of tons...

Martes 09 agosto 2022

Investment casting, also called the lost-wax casting process, is actually an ancient metal casting technology with a history of over 6,000 years. Investment casting mold generally refers to the mold made with meltable materials (such as wax, plastic, etc.) in very accurate dimensions...

Martes 09 agosto 2022

Sand casting means the main material consisting of the mold is sand, and the melted metal fills the casting cavity only by its gravity. Generally, this method of making the casting products is so-called sand casting. There are several different kinds of sand applying to industrial...

Martes 09 agosto 2022

Die Casting involves 3 key elements: the die casting machine, the mold, and the alloy materials, and the die casting could be described as the process of combining pressure, speed, and time to achieve an ideal cast metal part. The pressure applied during the casting process is a different...

Viernes 05 agosto 2022

MIM is a repeatable process for complex components made from high-temperature alloys. MIM parts are near fully dense, which provides excellent mechanical, magnetic, corrosion, and hermetic sealing properties, and allows secondary operations like plating, heat treating, and machining...

Viernes 05 agosto 2022

MIM stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a nearly unlimited shape, geometric-feature capability, high-production rates through the use of multi-cavity tooling. Compared with conventional technology like press sintered and CNC...

Viernes 05 agosto 2022

MIM stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a nearly unlimited shape, geometric-feature capability, high-production rates through the use of multi-cavity tooling. Compared with conventional technology like press sintered and CNC...

Martes 02 agosto 2022

Cantidad : 30-40sets/ - Precio : USD3000-200000

The same type of material of different colors is usually used for two-color injection overmolding（or 2k injection molding）so that the bonding strength of the first color and the second color plastic is the best, but due to the functional requirements of the product, the performance...

Martes 02 agosto 2022

Cantidad : 30-40sets/ - Precio : USD3000-200000

The runner filling balance must be considered when designing the multi cavity plastic mold in order to ensure the best effect of filling balance, the multi cavity mold will be multiple of 4 to design the mold generally, such as 4. 8. 16. 32. 64. 128 points, etc. ; Most of the multi-cavity...

Martes 02 agosto 2022

Cantidad : 30-40sets/ - Precio : USD3000-200000

Multi Cavity Medical Mold USM is an ISO9001: 2015 certified plastic moulding services factory, with over 15 years of professional experience and advanced equipment, we've got many successful cases in multi cavity soft plastic mold, there are 10 engineers could assist our customers...

Martes 02 agosto 2022

Cantidad : 30-40sets/ - Precio : USD3000-200000

Metal Insert Molding Choosing suitable material and molding conditions, not only for products that are easily deformed and damaged (such as glass, coils, electrical parts, etc.), can also be sealed and fixed by material. Choosing a suitable mold structure, the insert product can also...

Martes 02 agosto 2022

Cantidad : 30-40sets/ - Precio : USD3000-200000

Medical TPE Mold Design is the source of a high-quality mold, one good mold design will be half success, USM uses the world's leading software to analyze products and make DFM reports and mold flow analysis to eliminate the appearance of defective and defective products from the source...

Martes 02 agosto 2022

Prototype molds are rapid processing for the molds. It's totally different from production molds as they can't be used in the long term. As a professional mold maker for over 15 years,Packson can handle all kinds of mold including prototypes. We bring not only high skilled engineering...

Martes 02 agosto 2022

Precision mold components is a process that requires high technique and the use of precision molds and precision machines. The process of precision mould is different from normal injection mold but it still belongs to injection mold. It requires strict tolerance of ±0.01 mm and it...

Martes 02 agosto 2022

Multi cavity mould is an injection mold that has more than one cavity. The shape of each cavity is the same. Multi cavity mold design is to produce multiples of the same part for high volume production since it means each production will produce a large number of finished parts. Multi...

Martes 02 agosto 2022

2k injection molding is one type of injection mold. It is also named as two shot molding, double shot molding, double-color mold, Multi-material, or multi-component injection mold. 2k injection molding consists of two different plastic materials and colors. With over 15 years mold...

Viernes 29 julio 2022

Precio : 100USD

Genvan Silicones, founded in January 2008, is committed to the research and development (R&D), production, and sales of various kinds of Heat Cure Rubber (HCR) and Liquid Silicone Rubber (LSR). Genvan silicones rubbers supplies are certified as the national high-tech enterprise...

Miércoles 27 julio 2022

Cantidad : 1000 - Precio : 1 160,00 €

High-purity acid purifier: also known as acid purification system, high-purity acid purifier, acid reagent purifier, high-purity acid distillation purifier, etc. In laboratory work, due to the poor purity of acid, deviations and errors in analysis results are often caused . Commercially...

Jueves 21 julio 2022

The dental simulation unit is a medical-related model used in teaching to simulate dental patients. Most of dental sim units are made of metal and PVC materials. The teaching model of dental simulation vividly shows the functions and characteristics of patients when they see dental diseases...

Viernes 15 julio 2022

Cantidad : Per Order - Precio : $0.1-$200

Flanged bronze ball valve has the same action of rotating 90 degrees, the difference is that the cock body is a sphere, with a circular through hole or channel passing through its axis. The bronze copper ball valve is mainly used to cut off, distribute and change the flow direction...

Viernes 15 julio 2022

Cantidad : Per Order - Precio : $0.1-$200

The brass ball valves for water is evolved from the cock. Its opening and closing part is used as a sphere, which uses the sphere to rotate 90° around the axis of the valve stem to achieve the purpose of opening and closing. The ball brass valve can cut off, distribute and change...

Martes 12 julio 2022

GNS-5030 shrink tunnel packaging machine adopts the design of internal circulation air duct to ensure the uniform temperature in the furnace; Stainless steel heating tube, stable heating, and long service life; The outside of the conveying roller is wrapped with high-temperature resistant...

Sábado 09 julio 2022

Cantidad : 50 units/m - Precio : 80,000~180,000

Hot press vacuum press is used for the test parameters of the material properties, including the fluidity of composite materials, resin fluidity, and gel time. The composite material is formed after hot pressing and curing. The parameters of temperature and pressure in the hot pressing...

Sábado 02 julio 2022

Mould Slide The mould slider is a mold component that can slide in a certain angle perpendicular to or with the opening and closing direction during the opening and closing action of the mold. Features of Mould Slide When the product structure makes it impossible for the mold to demould...

Sábado 02 julio 2022

Insert molding is a precision injection molding process used to encapsulate a component in a plastic part. The insert plastic injection molding process can be divided into two basic steps. First, the component is loaded into the mold before the molding process. Second, it takes the...

Sábado 02 julio 2022

Home Appliance Part The development and design of plastic injection molding home appliance parts pay attention to safety and health. In-home appliance industry, polypropylene plastics are used extensively in washing machines and dishwashers. As one of the leading plastic injection...

Jueves 30 junio 2022

Cantidad : 1000 - Precio : 2000-4500USD

The frequency of linear probe is 4-12 MHz, which can be applied on ultrasonic examination of superficial organs, vessels, and tissues, etc. Compared with other linear probes, Stork linear probes have a more professional algorithm platform and GPU framework to ensure clear images....

Jueves 30 junio 2022

Description of Forged Ball Valve: ZECO forged ball valve is divided into forged two-piece ball valves and forged three-piece ball valves, as well as small diameter forged ball valves and large diameter forged ball valves, which are widely used in various high-pressure industrial conditions...

Miércoles 29 junio 2022

Prototype molds are rapid processing for the molds. It's totally different from production molds as they can't be used in the long term. As a professional mold maker for over 15 years,Packson can handle all kinds of mold including prototypes. We bring not only high skilled engineering...

Miércoles 22 junio 2022

Cantidad : 100000 - Precio : 60~3000USD

Motor Driven Diaphragm Pump Motor driven dosing pumps has to be strong and stable. Every series of NEWDOSE motor-driven dosing pumps offer a range of different models, with manual or automatic signal control (4-20mA), for viscous liquids, with different dosing systems, different parameters...

Miércoles 22 junio 2022

Precio : 5000USD-30000USD

A multi cavity mold can be understood, obviously referring to mold with multiple cavities. The multi 8 cavity mold comprises a multi-cavity of the same plastic part and a multi-cavity of different plastic parts. The use of multi-cavity molds for plastic injection molding of plastic...

Miércoles 22 junio 2022

Precio : 5000USD-30000USD

Insert Molding Technologies for Automotive Industry Mould Type: Automotive Sensor Plastic Injection Mould Production Material: Nylon PA66 No of Cavities: 4 cavities Core Material: S7 Cavity Material: S7 Mold base steel: 1.1730 with A/B plate 1.2312 Injection System: Cold runner Type of gating...

Miércoles 22 junio 2022

Cantidad : 1200sets/y - Precio : USD10000-200000

ZNC EDM Sinker has X and Y-axis manual control, and Z-axis automatic control. It can do one single job after manually set position, and job setting is also manual. Ideal for molds and spare parts manufacturing industries, ZNC edm die sinker product for sale by DMNC is your best...

Martes 21 junio 2022

8 Cavity Mold USM as a medical plastic injection mold supplier provides products including medical device plastic parts, suction tips, blood collection devices, pregnancy test sticks, culture tubes, ventilator masks, etc. If you want to know more types of shot glass mold silicone...

Martes 21 junio 2022

4 Cavity Injection Mold The multi-cavity mold can save production time, for example, one mold can produce 1 piece of part in one minute, but it can be produced 32 pieces of parts in one minute if we make a 32-cavity mold. Multi cavity mold requires very high machining accuracy. If...

Martes 21 junio 2022

32 Cavity Mold In terms of multi-cavity molds, we pay attention to the design of layout and runner filling balance, which is also the key to the success of multi-cavity molds. Product material: ABS material in medical-grade Mold steel: S136 HRC 52-54 Mold life: 1 million Hot runner brand...

Martes 21 junio 2022

The rotary mold is composed of two-cavity and core sides, the two core sides are the same, only the cavity sides is different which the second color cavity is bigger than the first color, at the beginning of injection molding, the barrel of the two-color injection molding machine...

Miércoles 15 junio 2022

Precio : 10-30USD

LCD TV Mould TV screen frame mold is used to produce TV screen frames, it should be strong and assembly well with the screen. It has an undercut to lock the screen inside stablely. For the TV screen frame mold, we usually make one cavity mold, because of its big size, the injection...

Miércoles 15 junio 2022

Precio : 10-30USD

Mainly electronic molds we make are electronic housing mold, electronic components mold, electronic dashboard cover mold, computer keyboard mold, computer mouse mold, bluetooth earphone plastic mold, power bank enclosure mold, air purifier mold, plug plastic mold, gamepad mold etc...

Miércoles 15 junio 2022

Precio : 10-30USD

The family mold is used to produce injection parts for liquid filtration and flow monitoring and control systems. These accessories are customized made for Rotational Filter and Flow Limiting equipment and devices. There are two parts which are assembled together, one is hat shape...

Miércoles 15 junio 2022

Precio : 10-30USD

If the weight of each fan blade is not balanced, large vibration, high noise, and large wear of the rotating shaft will occur during high-speed rotation, which not only seriously affects product performance, but also The lifetime will also be greatly reduced. Therefore, fan products...

Martes 14 junio 2022

Multi cavity mould is an injection mold that has more than one cavity. The shape of each cavity is the same. Multi cavity mold design is to produce multiples of the same part for high volume production since it means each production will produce a large number of finished parts. Multi...

Martes 14 junio 2022

Precision injection molding is a process that requires high technique and the use of precision molds and precision machines. The process of precision mould is different from normal injection mold but it still belongs to injection mold. It requires strict tolerance of ±0.01 mm and...

Martes 14 junio 2022

With more than 20 years of experience in the injection molding industry and equipped with ISO Class 8 Clean Room, Packson plastic injection moulding factory offers Medical Contract Plastic &Rubber Injection Molding, Custom Injection Molding, Insert Molding and Over Molding by...

Martes 14 junio 2022

We provide custom made plastic parts-Sliders, inserts, lifters, blocks, ejector pins, and other mold components for our worldwide clients in 3 days via DHL or TNT. We are able to manufacture custom made plastic parts(Mold slider, lifters, Mold inserts, Core and cavity, blocks, ejector...)

Martes 14 junio 2022

Packson provides our customers a various CNC machining services to our customers, including milling, turning, grinding, drilling and more. Our teams are able to manufacture metal machining parts via our precision manufacturing machine such as 3,4, and 5 axis CNC machining centers...

Martes 14 junio 2022

MIM China stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a nearly unlimited shape, geometric-feature capability, high-production rates through the use of multi-cavity tooling. Compared with conventional technology like press sintered and CNC...

Martes 14 junio 2022

MIM stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a nearly unlimited shape, geometric-feature capability, high-production rates through the use of multi-cavity tooling. Compared with conventional technology like press sintered and CNC, MIM...

Martes 14 junio 2022

MIM stand for metal injection molding china, it's a forming method of a metal parts and can provide a nearly unlimited shape, geometric-feature capability, high-production rates through the use of multi-cavity tooling. Compared with conventional technology like press sintered and CNC...

Martes 14 junio 2022

MIM tablet stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a nearly unlimited shape, geometric-feature capability, high-production rates through the use of multi-cavity tooling. Compared with conventional technology like press sintered and CNC...

Viernes 10 junio 2022

What is exothermic welding machine Exothermic welding, also called hot melt welding, fire-clay welding, thermite welding and explosion welding, is a high-heat principle that utilizes the redox reaction between metals, the operation of which is simple, easy to learn, safe and efficient...

Viernes 10 junio 2022

Clad Steel Definition 0.8 Series CCS Round Wire Origin of new material development 0.8mm series copper-clad round wire is a new type of material developed by our Company to replace pure copper. Because it has the advantages of high strength, low price, high corrosion resistance and...

Miércoles 08 junio 2022

The satellite earth antenna is the important earth satellite equipment to collect the weak signal from satellite and reduce noise to the lowest level within its ability. The traditional materials for satellite antenna are iron or aluminium. But the better properties of SMC material...

Martes 07 junio 2022

Specs of Larger Low Speed Refrigerated Centrifuge LC-450R Driven by AC frequency conversion motor with quiet and clean running. Imported refrigeration compressor 9 kinds of ascending and descending rate of choice 20 kinds of custom work mode section Speed mutually establish/centrifugal force...

Martes 07 junio 2022

Specs of High Speed Refrigerated Centrifuge HC-3618R Microcomputer control, LCD liquid crystal display(LCD) Imported refrigerating compressor, high refrigeration efficiency AC frequency conversion motor drive, quiet operation clean Offers nine ascending and descending rate selection modes...

Martes 07 junio 2022

Specs of High Speed Refrigerated Centrifuge HC-3616R AC frequency conversion motor drive, quiet operation clean. Offers nine ascending and descending rate selection modes, Offer ten kinds of working mode selection, can free programming call. Speed/centrifugal force can be set and...

Martes 07 junio 2022

Description of High Speed Refrigerated Centrifuge HC-3016R High Speed Centrifuge features desk-top construction and novel appearance design. It has AC frequency control, rotation speed and centrifuging time controller by microcomputer, working parameters set via the keyboard, digital...

Martes 07 junio 2022

Description of High Speed Refrigerated Centrifuge HC-2518HR High Speed Centrifuge features with table type, and is diven by AC frequency conversion motor. The high speed centrifuge has a microcomputer to control the rotation speed and centrifuging time controller. Its maximum speed...

Jueves 26 mayo 2022

Due to the less mismatched lattice and stable chemical and physical properties, sapphire(Al2O3) wafer is the popular substrates for III-V nitrides, superconductor and magnetic epi-film. They are widely used in GaN and thin-film epitaxial growth, silicon on sapphire, LED market and...

Miércoles 25 mayo 2022

Features of Cassava Grinding Machine Processing Capacity: 3-6Tons/hour Application Scope: Grating the cassava into the slurry. Product Introduction: Cassava grater machine, cassava grating machine, cassava grinder, cassava grinding machine for cassava flour and Garri processing. 1...

Miércoles 25 mayo 2022

RPS-20M wireless cnc probe system contains RP610M touch probe, RSI-20M receiver and standard measuring software. The RP610M is a compact spindle probe with radio signal transmission which offers automated part set-up and in-cycle gauging on machining centers, including 5-axis machines...

Miércoles 25 mayo 2022

The radio communication probe system is suitable for various complex working conditions in the processing of CNC machine tools, mainly suitable for large-scale machine tools, multi-axis machine tools and other CNC equipment, to avoid the influence of signal transmission strength by...

Martes 24 mayo 2022

Cantidad : 100000 - Precio : 1 000,00 €

Control Plug Valve can rotate 90° to connect or cut the medium. Body cavity with grooves and convex edges structure design can fix sleeve effectively, which can meet special application need. The design can protect valves avoid from the sleeve and plug rotation at the same time which...

Martes 24 mayo 2022

Cantidad : 100000 - Precio : 1 000,00 €

Ball valves are used to cut off or connect the medium in the pipeline, as well as to regulate and control the fluid. As a professional manual ball valve manufacturer, we can provide you with all kinds of floating and trunnion mounted ball valves. Ball valves mainly feature compact...

Viernes 20 mayo 2022

A dielectric mirror, also known as a Bragg mirror, is a type of mirror composed of multiple thin layers of dielectric material, typically deposited on a substrate of glass or some other optical material. By careful choice of the type and thickness of the dielectric layers, one can...

Viernes 20 mayo 2022

Adapter is one of the most important part of G.E.T system, especially the cast lip system. Either made by casting or forging, an adaptor installed between the lip and the tooth. It's nose and pocket support the main structure. WALKSON mainly focus on providing big size cast adaptor...

Miércoles 11 mayo 2022

Precio : 1-50000000

Recycling Chapter BAR Good Quality High Precision Recycling Chapter As a mould making company, we provide you with different types of injection molding with metal inserts and outsert molding, such as overmoldin`g insert molding, cavity insert injection molding, metal insert plastic...

Miércoles 11 mayo 2022

Precio : 100USD

Electronics Product Part With the fast growth in the electronic industry, the demand for injection molding electronics is much higher. The injection molding electronics can be intricate or simple. Intricate injection molding electronics can be economical because they combine many...

Miércoles 11 mayo 2022

Precio : 100USD

Decades of accumulation of mould manufacturing technology have witnessed the popularity of electrical plastic molding products. The electronics plastic injection mold has been widely applied to various industries. As a result, electronics plastic moulded products manufacturers have...

Miércoles 11 mayo 2022

Precio : 100USD

Die casting mould is a method of casting liquid die forging. It is a process completed in a special die casting moulding machine. The major advantage of mould die casting is that thousands of castings can be produced quickly by die casting mould supplier, die casting mould factory...

Miércoles 11 mayo 2022

Precio : 100USD

2k moulding is a manufacturing process that refers to molding two materials or colors into one plastic part. This technology combines two materials or two colors into one ending plastic part by using a 2K automotive plastic injection moulding machine. The selection of the 2K moulding...

Viernes 29 abril 2022

Brief Introduction of Hanking ABS molds Mould Name: Plastic Injection ABS Molds Part Material: ABS Product Size: 172*123 mm Product Description: clear window Mould Cavity: 1 Cavity Mould Size: 300*380*250 mm Mould Cavity Steel: ASSAB 8407 Mould Injection System: hot runner Mould Ejection System...

Viernes 29 abril 2022

Custom Injection Mould Making Services for Auto Parts Mould Type: Automotive Final Sensor Production Material: 33% glass fiber reinforced, black PA 6/12 No of Cavities: 4 cavities Core Material: S7 Cavity Material: S7 Mold base steel: 1.1730 with A/B plate 1.2312 Injection System...

Miércoles 20 abril 2022

Cantidad : 500000 Pie - Precio : US $1 - 3,000 / Set

Festures of Pressure Relief Valve Accurate Pressure Control Fast Opening to Maintain Line Pressure Slow Closing to Prevents Surges Completely Automatic Operation Pressure Relief Valve Working Principle Inlet pressure water enters the lower cavity of the pilot valve diaphragm from...

Miércoles 20 abril 2022

Description: Plastic Valve 3 Plate Mould Tolerance: +-0.01mm Surface: SPI A2 & VDI 3400 Part material: PPO food grade Shrinkage: 0.6% Cavity steel: ASSAB 8407 HanKing Mold Tolerances Plates and Mold Base Components: ± 0.013 mm (± 0.0005 in) Cavity components: ± 0.005 mm (± 0.0002...)

Miércoles 20 abril 2022

Mould Name: Adapter Charger Housing Mould Part Material: PC Product Size: 58.3*57.9*8.6mm Product Description: Adapter Charger Housing UK Mould Cavity: 4 Cavities Mould Size: 400*450*343MM Suitable Injection Machine: 160 ton Mould Cavity Steel: ASSAB8407 Mould Injection System: Cold...

Martes 19 abril 2022

Prototype molds are rapid processing for the molds. It's totally different from production molds as they can't be used in the long term. As a professional mold maker for over 15 years,Packson can handle all kinds of mold including prototypes. We bring not only high skilled engineering...

Martes 19 abril 2022

Precision mold components is a process that requires high technique and the use of precision molds and precision machines. The process of precision mould is different from normal injection mold but it still belongs to injection mold. It requires strict tolerance of ±0.01 mm and it...

Martes 19 abril 2022

Multi cavity mould is an injection mold that has more than one cavity. The shape of each cavity is the same. Multi cavity mold design is to produce multiples of the same part for high volume production since it means each production will produce a large number of finished parts. Multi...

Martes 19 abril 2022

2k injection molding is one type of injection mold. It is also named as two shot molding, double shot molding, double-color mold, Multi-material, or multi-component injection mold. 2k injection molding consists of two different plastic materials and colors. With over 15 years mold...

Sábado 16 abril 2022

LEFOO diaphragm pump for water purifier 115V is an RO water pump. The diaphragm pump for water purifier 115V is supplied with alternating current (AC), and the AC voltage is capable of being set as a 115v water pressure pump, which is rectified into a direct current (DC) voltage through...

Sábado 16 abril 2022

Longguang' products have a wide range of applications in the automotive field. We also have close cooperation with various automobile industry manufacturers in China over ten years, such as Toyota and Bosch, which has also accumulated a lot of experience and cases in this industry...

Sábado 16 abril 2022

Under many circumstance, due to the limitation of equipment, it is necessary to use manual equipment to grind the parts such as angle grinder. At these time, many small types of brush, such as pipe brush, end brush, we can design the size of the shank according to the specifications...

Jueves 14 abril 2022

Cantidad : 50000 sets - Precio : USD25-80

POER Smart provides the programmable wifi central heating thermostat set. We have wifi water heater thermostats and electric underfloor heating thermostat wifi for your choice. The wifi boiler control thermostat was built-in a wifi module. With this module, the wifi thermostat underfloor...

Martes 12 abril 2022

Cantidad : 1200sets/y - Precio : USD10000-200000

Wire Erosion Machines for Sale DMNC Provides Complete Solution Of EDM Machining Technology With 30+ Years' Experience, Continuous Innovation, Strict Quality Control, and Swift Service. The CNC EDM machine for sale can machine deep ribs faster with more precision, as the CNC incorporates...

Martes 12 abril 2022

Precio : 100USD

What is exothermic welding supplies Exothermic welding, also called hot melt welding, fire-clay welding, thermite welding and explosion welding, is a high-heat principle that utilizes the redox reaction between metals, the operation of which is simple, easy to learn, safe and efficient...

Jueves 07 abril 2022

The nozzle of cooling tower is the component of water distribution in the cooling tower, which is made of ABS by one-time injection molding. Socket connection, firm connection, easy disassembly, not easy to block, nozzle water distribution is uniform, using cross water distribution method...

Jueves 07 abril 2022

Railroad Clip Steel MIM stand for Metal Injection Molding, it's a forming method of a metal parts and can provide a nearly unlimited shape, geometric-feature capability, high-production rates through the use of multi-cavity tooling. Compared with conventional technology like press...

Jueves 07 abril 2022

MIM Products Whether you seek to economically manufacture a high-quality computer component, a small medical instrument, a firearm component, or other metal injection molding products, MIM is an ideal process. Wearability And Smart Wearability In recent years, wearable devices have...

Sábado 02 abril 2022

Cantidad : 1000 - Precio : 2000-4500USD

The frequency of the linear array probe is 4-12 MHz, which can be applied on ultrasonic examination of superficial organs, vessels, and tissues, etc. Compared with other linear probes, Stork linear probes have a more professional algorithm platform and GPU framework to ensure clear images...

Sábado 02 abril 2022

Cantidad : 1000 - Precio : 2000-4500USD

An ultrasonic sensor or a probe generates sound waves, and the reflections of the sound waves produce clear images of body tissues and organs, which is an important part of the ultrasound system. The following are the three most common ultrasonic probes types: Linear ultrasound probe...

Martes 29 marzo 2022

The vacuum pressure casting, as this name indicates, is casting method which the major processes including the melting, pouring, solidifying are performed inside the vacuum chamber. The vacuum is able to minimum the gas content of the product, and prevent further oxidation happening to the metal...

Martes 29 marzo 2022

The squeeze die casting, also names extrusion casting or liquid die forging, is kind of newly developed metal forming technic which combines the casting process and die forging like method. The basic principle is to fill the liquid metal into the pre-lubricated mold cavity, then gives...

Miércoles 16 marzo 2022

Pressure Sensor Definition The pressure sensor produced by Tianguang company can be divided into resistance strain type and diffused silicon type. According to the structure, each type is divided into two types: with a cavity and without a cavity. The cavity has high accuracy and a wide range...

Miércoles 16 marzo 2022

Precio : 1000-6000USD

Hot Press Vacuum Press for Sale Hot vacuum press is used for the test parameters of the material properties, including the fluidity of composite materials, resin fluidity, and gel time. The composite material is formed after hot pressing and curing. The parameters of temperature and...

Miércoles 16 marzo 2022

Precio : 100USD

Adapter is one of the most important part of G.E.T system, especially the cast lip system. Either made by casting or forging, an adaptor installed between the lip and the tooth. It's nose and pocket support the main structure. WALKSON mainly focus on providing big size cast adaptors...

Martes 15 marzo 2022

Methyl methacrylate china, whose chemical formula is C5H8O2 and chemical formula quantity is 100.12, is an organic compound, also known as MMA, or methyl ester for short. HS code for MMA is 2916140010. MMA methacrylate is an important chemical raw material and the production of...

Viernes 11 marzo 2022

Precio : 100USD

Differential Pressure Gauges Differential vacuum gauge measure the difference between two pressures. They are suitable for the monitoring of filter contamination, for level measurement in closed vessels, for overpressure measurement in clean rooms, for flow measurement of gaseous...

Jueves 10 marzo 2022

AX Series (AX-400, AX-500, AX-600, AX700, AX-800, AX-900) portable anaesthesia machine offers SIMV supports the smooth transition to anesthesia resuscitation, promotes resuscitation efficiency, and reduces lung injury caused by man-machine confrontation. CPAP/PSV supports postoperative...

Jueves 10 marzo 2022

The remarkable Acclarix AX2 & AX3 color doppler ultrasound scanner System delivers a surprising combination of features to meet the demands of point-of-care imaging. It has been designed from the relentless focus on delivering uncompromising performance at a cost-effect price...

Jueves 10 marzo 2022

Cantidad : 30-40sets/ - Precio : USD3000-200000

For plastic medical device manufacturers, it means that medical supervisors are required to supervise and manage the materials used to manufacture the equipment, the medical injection molds parts are designed to withstand high temperatures and chemical corrosion. In this way, it...

Jueves 10 marzo 2022

Cantidad : 30-40sets/ - Precio : USD3000-200000

Gas & Water assisted injection molding Since the thermal conductivity and heat capacity of water are much bigger than nitrogen, so the injection cycle of water-assisted is about 70% shorter than the injection cycle of gas-assisted molding; The product wall thickness of water-assisted...

Jueves 10 marzo 2022

Precio : 1000-6000USD

Precision Mould Parts Various high-precision parts As a precision molding company, we spare no efforts to provide precision moulded components to achieve our customers' satisfaction. If you have any questions about our parker precision molding, please do not hesitate to contact us...

Jueves 10 marzo 2022

Precio : 1000-6000USD

Hot Runner Mould for Pump Base Hot Runner Molds for Water Pump Bases The hot runner injection molding process is an advanced concept of thermal engineering which refers to moulds using a heated device to make them melt in the runner never solidify. We provide you with different types...

Miércoles 09 marzo 2022

Precio : 100USD

Two shot molding, also called double shot moulding, dual shot injection molding，multi shot injection molding or 2k injection moulding is one category of injection molding using two different thermoplastic materials to produce injection molded parts in two colors or two components...

Miércoles 09 marzo 2022

Precio : 100USD

Plastic molds are tools that are matched with plastic mold making machines in the plastic processing industry to give plastic products a complete configuration and precise dimensions. Due to the wide variety of plastics and processing methods, and the complex and simple structures...

Miércoles 09 marzo 2022

Precio : 100USD

What is plastic injection molding? Plastic Injection molding is a molding method that combines injection and molding. The advantages of plastic injection molding method are fast production speed, high efficiency, operation can be automated, variety of colors, shapes can be from simple to complex...

Miércoles 09 marzo 2022

Precio : 100USD

What material is used in injection moulding？Materials used in injection moulding generally include pla molding, nylon injection molding, polypropylene plastic injection molding, pp injection moulding, pvc injection molding, hdpe injection molding and so on. Injection moulding raw...

Martes 08 marzo 2022

A multi cavity mold is known as a mould with multiple cavities. The multi-cavity mold consists of a multi-cavity of different plastic parts. Though multi-cavity plastic injection molding process may be much more complex than others such as insert injection molding process, it is still...

Martes 08 marzo 2022

The slider is a mold component that can slide in a certain angle perpendicular to or with the opening and closing direction during the opening and closing action of the mold. Features of Mould Slide When the product structure makes it impossible for the mold to demould normally without...

Martes 08 marzo 2022

Medical Equipment Mould Medical device injection molding is a process using medical-grade plastic materials to manufacture different durable medical parts and components. The medical device plastic injection molding process can provide benefits for a variety of applications such...

Martes 08 marzo 2022

Insert Mould Insert molding is an injection molding process used to encapsulate a component in a plastic part. The insert injection molding process can be divided into two basic steps. First, the component is loaded into the mold before the molding process. Second, it takes the shape...

Martes 08 marzo 2022

Dental lab productsThe dental laboratory is a place to complete all the tasks that the patient does not participate in the oral medicine, such as making dentures, model making, polishing, etc. The laboratory with good conditions can carry out porcelain teeth, casting brackets, etc...

Martes 08 marzo 2022

BALL VALVES As one of pneumatic ball valve suppliers , MstnLand provides high performance ball valve products, including Trunnion mounted ball valve, Floating ball valve, Welded structure ball valve, Top entry ball valve, Wafer ball valve, Butt treaded socket welding ball valve...

Domingo 27 febrero 2022

Alginate wound dressing is an advanced moist wound dressing, composed of biodegradable, highly absorbent alginate fiber which is derived from seaweed, available in flat and rope patterns. On contact with exudate, these dressings form a moist gel through a process of ion exchange...

Domingo 20 febrero 2022

Cantidad : 20,000 ton - Precio : $850~$2000 / ton

Sand casting is the most commonly applied method for casting the metal part. It suits most of the raw materials, ferroalloy, and non-ferroalloy both can be used to do the sand casting. Sand casting is able to produce the part varying from several gram weight to dozens of tons, or...

Domingo 20 febrero 2022

Cantidad : 20,000 ton - Precio : $850~$2000 / ton

Investment casting, also called the lost-wax casting process, is actually an ancient metal casting technology with a history of over 6,000 years. It generally refers to the mold made by meltable materials (such as wax, plastic, etc.) in very accurate dimensions. The mold is applied...

Domingo 20 febrero 2022

Cantidad : 20,000 ton - Precio : $850~$2000 / ton

Sand casting means the main material consisting of the mold is sand, and the melted metal fills the casting cavity only by its gravity. Generally, this method of making the casting products is so-called sand casting. There are several different kinds of sand applying to industrial...

Domingo 20 febrero 2022

Cantidad : 20,000 ton - Precio : $850~$2000 / ton

The Die Castng involvs 3 key elements: die casting machine, the mold and the alloy materials, the die casting could be described as the process of combining pressure, speed and time to achieve a ideal casted meatal part. The pressure applied during the casting process is the different...

Domingo 20 febrero 2022

As a metal injection molding manufacturer, Jinchuan Group Co., Ltd. is a conglomerate engaged in mining, mineral processing, smelting, chemical engineering, and value-added processing. Our main products are nickel, copper, cobalt, platinum group metals, non-ferrous metal products...

Domingo 20 febrero 2022

As a metal injection molding manufacturer, Jinchuan Group Co., Ltd. is a conglomerate engaged in mining, mineral processing, smelting, chemical engineering, and value-added processing. Our main products are nickel, copper, cobalt, platinum group metals, non-ferrous metal products...

Domingo 20 febrero 2022

As a major metal injection molding factory, Jinchuan Group boasts the third largest copper-nickel sulfide deposit in the world, and serves as both China's largest and the world's leading nickel and cobalt production base and platinum group metal refining center. MIM stand for Metal...

Domingo 20 febrero 2022

Packson provides our customers a various CNC machining services to our customers, including milling, turning, grinding, drilling and more. Our teams are able to manufacture metal machining parts via our precision manufacturing machine such as 3,4, and 5 axis CNC machining centers...

Domingo 20 febrero 2022

2 component injection molding is one type of injection mold. It is also named as two shot molding, double shot molding, double-color mold, Multi-material, or multi-component injection mold. two colour injection moulding consists of two different plastic materials and colors. With...

Jueves 10 febrero 2022

Precio : 50,00 €

iWORKHUB's Mobile Cart Rotational is designed to support the features and functions of the 50.5" Microsoft® Surface™ Hub 2S/2X, 55" and 65" Samsung Flip 2 displays. These commercial monitor floor television carts/stands on wheels can effectively allow the display to rotate from landscape...

Jueves 10 febrero 2022

Founded in 1991, located in Hangji Industrial Park of Yangzhou City, PERFECT GROUP CORP., LTD. was established as a professional and world-class manufacturer of PERFECT toothbrushes, electric toothbrushes, toothpaste, dental flosses, flosser, interdental brush, perfect denture tablets products...

Viernes 28 enero 2022

We are a plastic injection manufacturer. In the spirit of a "one-stop-shop", our own tool workshop as well as an assembly and an international sales service. We have an precision injection molding process with a component load capacity of up to 2 kg in a large machine, carrying out...

Domingo 09 enero 2022

Cantidad : 20000pcs p - Precio : $0.5-200.00

A dielectric mirror, also known as a Bragg mirror, is a type of mirror composed of multiple thin layers of dielectric material, typically deposited on a substrate of glass or some other optical material. By careful choice of the type and thickness of the dielectric layers, one can...

Viernes 31 diciembre 2021

We are a plastic injection manufacturer. In the spirit of a "one-stop-shop", our own tool workshop as well as an assembly and an international sales service. We have an precision injection molding process with a component load capacity of up to 2 kg in a large machine, carrying out...