Pneumatic Terminal Crimping Machine
Pneumatic Terminal Crimping Machine
-
Cable Hydraulic Crimping Machine BJ-30T
* Force: 20Ton
* Applicable Scope: 1-200mm² wire
* Stroke: 50mm Adjustable
* Power: 220V/110V
* Size: 60*28*60cm -
BJ-607E Pneumatic Terminal Crimping Machine
* Crimping range: 10-300mm2
* Air pressure range: 0.5-0.8MPa
* Output: 9.0T
* Overall dimension: 400*200*210mm
* Weight: 10.5kg -
BJ-1200 Pneumatic Crimping Machine
* Crimping range: non-insulated terminals≤10mm²
* Pre-insulated terminals: ≤6mm²
* Tube-shaped terminal: ≤25mm²
* Output: 13.5kg
* Pressure range: 0.4-1MPa -
BJ-602E Pneumatic Terminal Crimping Machine
* Crimping range: 0.5-16mm²
* Air pressure range: 0.5-0.8Mpa
* Output: 1.8T
* Voltage range: AC 220V
* Weight: 6kg
* Overall dimension: 275*128*145mm -
BJ-606E Pneumatic Terminal Crimping Machine
* Range of Application: 6mm(insulated terminal)//35mm2(Furcate terminal)
* Air pressure range: 0.4-1Mpa
* Output force: 13.5KN
* Voltage range: AC 220V
* Weight: 6.5kg
* Overall dimension: 260*120*140mm -
BJ-603E Pneumatic Type Terminal Crimping Machine
* Crimping range: Non-insulated terminal 0.5-50mm² ≤
* Air pressure range: 0.6-1Mpa
* Output: 2.5T
* Voltage range: AC 220V
* Weight: 6kg
* Overall dimension: 286*125*165mm -
BJ-604E Pneumatic Type Terminal Crimping Machine
* Crimping range: Tube terminal 0.08-120mm²
* Air pressure range: 0.5-0.8Mpa
* Output: 2.5T
* Voltage range: AC 220V
* Weight: 6.5kg
* Overall dimension: 360*125*165mm
Operation steps of terminal machine
1. Turn on the switch of the terminal crimping machine source, and the power indicator lights.
2. Pay attention to whether there is a noticeable difference in the inside and outside of the machine. If there is a suspension, please check whether the maintenance is needed.
3. Choose and install the knife: it is operated by the designated personnel, and it is necessary to perform the manual comparison with the selected blade before loading the knife. It can be operated without error. Knife installation is completed, the manual test must be used. Firstly turn off the terminal mechanical and electrical source, cut touch button, using a dedicated plate loom, master-slave pulley. The terminal machine stamping trip to maximum, for that hand did not move, considering whether stress or other problems, checking the debug to be OK. The lock screws should be checked and confirmed before the operation.
4. Loading: Install the terminals that need to be hit, use the Allen wrench to adjust feed clamp, and the terminal can easily pass, visual feed position whether appropriate, if not, adjust it, using the Allen wrench to loosen feeder lock screw, a screw dynamic adjustment of the level. Until it is in the best status, then lock feeder and lock screw, begin to work.
5. Testing tension: After the machine is OK, try to take waste wire, tensile test, the main reference value to see "the pull test table" for the specific operation method is as follows, press the tension test the zero key to zero. The terminal wire clip will need to be tested. If the test strain is beyond the scope of standards, the mechanics will adjust it again until reaching the standard value.
6. Trial 10 PCS is sent for the first IPQC to be confirmed that the inspection is OK, which can volume production. In the process of production, the operator must self-check whether the terminals having the plastic bags, hanging, etc. are poor, testing a terminal tensile every 1 hour.
7. Tidy up fine products and waste products after production, cleaning up the surrounding environment sanitation of the machine station.
- 11th Floor, Jingzuan Building, NO. 875 Xiaolin Road, Kunshan, Jiangsu, P.R.C.
- Phone: +86-512-57169166
- Fax: +86-512-57799757
- E-Mail: salome@bojin.hk
- Web: http://www.bojin.hk/products/pneumatic-terminal-crimping-machine/
Persona a contactar : Lee Salome, 0086 0512 57169166
Buen trato: comprar del vendedor
Por favor, lea nuestras condiciones de uso. También puede visitar nuestras preguntas frecuentes y ver nuestra información sobre los riesgos relacionados con la falsificación.
Esta página es acerca de los importadores y exportadores de Pneumatic Terminal Crimping Machine Buscar en la categoria : Bienes de equipo Buscar en la categoria : terminal, machine, crimping, pneumatic |
Lunes 20 agosto 2012
Cantidad : une machin - Precio : 30000euros
Ubicación : Calle Prado Isidro 45 , 28492 Mataelpino Madrid, Persona a contactar : Allami Azizi cherifa, 639509955
autonomo
- 28492 - Mataelpino Madrid
- 639509955
Lunes 07 diciembre 2009
Nous recherchons un importateur distributeur exclusif par pays Notre gamme de produits : Bouteilles 1.5l par 6 et bouteilles de 50 ml par 12. TEL : 00 230 433 99 99 Fax : 00 230 433 99 98 Île Maurice Ubicación : Sodibo ltd Moka business Centre Montagne Ory Road Bon Air Moka Mauritius...
Sodibo ltd.
- - Moka
- 00 230 433 99 99
- +33 6 27 70 58 57
Viernes 22 junio 2012
Cantidad : 2000 T - Precio : 0,62 €
- somos una sociedad de exportación de cítricos de Marruecos en Ouled Teima (famoso de la producción de la mejor cantidad y calidad de los cítricos en el mundo). Ponemos a la venta una gran cantidad de Agüimes Clémentine Nulis Nova Nour Maroc finales Navil Citron. etc ... - Ubicación ...
LIMONA D'ORIGINE
- limonadorigine
- 18350 - agadir
- 00212660899072
- 00212652109469
- +212652109469